English
Shipping to:
Shipping to:

Dynotest for BMW 8 Series - G14, G15, G16, F93
2018-2024

€ 307.50
(incl. taxes)

Previous lowest price was € 307.50.

Product code : DNTBMWG

Product Information

Pay attention!

The (BC) will not function properly because it cannot calculate values without having the mileage and it's NORMAL. When the device is activated, the on-board computer readings ("Average fuel consumption", "Current fuel consumption", "Fuel") and the navigation monitor ("On-board information" or "Trip computer", "Cruising range", "Distance to destination", "Fuel economy") will have incorrect values. After deactivating the device, you must RESET the on-board computer from the BC and the navigation menu. The BC will then start working correctly again.

Adaptive cruise control, ACC and radar work in all modes!

This device is specifically designed for testing BMW 8 Series - G14, G15, G16, F93 cars.

It provides the capability to temporarily suspend (freeze) the odometer during car testing, preventing the accumulation of additional mileage.

Installing this device may cause the displayed average and current fuel consumption to be higher than the actual values.

It is not intended to be used on public roads.

The Plug&Play technology eliminates the need for soldering during installation.

Simply follow the video instructions for proper connection.

€ 307.50Add to basket

How to install
BMW 8 Series - G14, G15, G16, F93

Dashboard

Button

Information about the operation modes of the device on BMW 8 Series - G14, G15, G16, F93 cars.

The hazard warning light on the dashboard will blink each time the device switches between modes.

1
Mode 1
Press and hold the "BC" button for 10 seconds.
The hazard warning light will blink once.
The mileage block function will be not active.
Speedometer will show the actual speed.
2
Mode 2
To activate this mode, press and hold the "BC" button for 10 seconds.
The hazard warning light will blink twice.
The odometer will register 40 km for every 100 km driven.
Speedometer will show the actual speed.
3
Mode 3
Press and hold the "BC" button for 10 seconds.
The hazard warning light will blink three times.
The odometer will register 30 km for every 100 km driven.
Speedometer will show the actual speed.
4
Mode 4
ONLY for cars with software update BEFORE 2019.
Press and hold the "BC" button for 10 seconds.
The hazard warning light will blink four times.
The odometer will register 1-2 km for every 100 km driven.
Speedometer will show the actual speed.
5
Mode 5
Press and hold the "BC" button for 10 seconds.
The hazard warning light will blink five times.
The odometer will register 1-2 km for every 100 km driven.
Speedometer will NOT show the actual speed.

Dynotest for BMW 8 Series – G14, G15, G16, F93 (2018–2024)

Dynotest for BMW 8 Series G14, G15, G16 and F93 (2018–2024) is a professional electronic solution designed for precise control of mileage recording during diagnostic procedures, performance testing and service works. This advanced mileage blocker device allows you to temporarily stop mileage counting in the instrument cluster and related control units while the vehicle is being tested on a dyno bench or transported for technical purposes.

The module works as a reliable mileage blocker, also known as mileage stopper or odometer blocker, ensuring that unnecessary kilometers are not added during chip tuning, ECU programming or system diagnostics. For workshops and performance centers working with premium models such as BMW 8 Series, an odometer stopper is an essential tool to maintain accurate service history and avoid artificial mileage increase during stationary tests.

Our milage blocker is fully compatible with the electronic architecture of BMW G14 Convertible, G15 Coupe, G16 Gran Coupe and F93 M8 models produced from 2018 to 2024. The installation is safe and does not damage vehicle systems when used correctly for off-road, testing or service purposes. After deactivation, the vehicle operates in standard mode without leaving warning messages or errors.

Choose a high-quality Mileage blocker device developed specifically for BMW 8 Series and ensure professional control over mileage data during tuning and diagnostic operations.

IMPORTANT FOR SUCCESSFUL INSTALLATION AND USE

1. During device connection/disconnection, the ignition must be turned off.
2. Switching between modes should be done on a stationary car.
3. When the device is in use, the selected mode will be retained (saved) after the ignition is turned off/on.

OTHER, ALTERNATIVE PRODUCT NAMES SEARCHED FOR:

Mileage Blocker, Mileage Stopper, Odometer Stopper, Odometer Blocker, Mileage Correction, CAN Filter, CAN Blocker, Mileage Freezer, Odometer Freezer, CAN Freezer.

SERVICE CENTER

CUSTOMER CENTER →
SHIPPING →
TECHNICAL SUPPORT →
INSTALLATION SUPPORT →
Select your currency
EUR Euro
PLN Polish złoty
USD United States (US) dollar

ATTENTION!

The use of this device is intended for lawful purposes only. Using it may result in loss of guarantee coverage from your car manufacturer.